• (702) 910-4913
  • Fast and Free Delivery To The US Only!
  • Free Tech Support For Life

4.6Out of 134 Reviews

Christmas Deals Call Now (702) 910-4913 Free Shipping to US only!

    Product description

    The Platter

    The platter has been upgraded with 12 brass inserts and one top brass insert under vinyl top plate add additional weight and further stabilize the platter for even better speed stability. It consists of two parts. The first part uses a soft alloy, the second part, a harder one. This reduces energy flow. The first part also incorporates the neodymium magnets. The platter weighs more than 22 kg. The diameter of the platter is 400 mm (not the usual 300 mm). This means that with the same weight you gain more moving mass on the platter. The platter also incorporates sorbothane damping to make it resonance free.

    The Bearing

    The bearing is not standard but inverted with an oversized polished shaft. The new platter with its huge mass creates more energy, which has to be absorbed better. Therefore we designed a new bearing block with a chrome alloy able to withstand more energy and damp the entire system more effectively. In addition the bearing spindle has a new "Movic" coating with the lowest friction coefficient possible (6 times less than previous spindle versions). This is the same coating that is used by NASA for bearings in satellites.

    A ceramic ball is used on the top because it is very hard and inert. This, in combination with a Teflon plate as a bearing mirror, is also a good damping device. Teflon's accurate satin surface produces perfectly smooth movement without any rumble. The platter has a magnetic suspension using neodymium magnets. By increasing the distance from the bearing to the cartridge, the small neodymium magnets eliminate magnetic infl uence on the cartridge. Due to the magnets we can still move a large mass allowing the bearing to see virtually no pressure. This avoids rumble. (A mass loaded platter usually causes high levels of rumble.) The pressure of the bearing is adjustable. There are different philosophies about the bearing pressure. With the Forte turntable you can adjust it according your preferences and taste..

    The Motor

    (applies only to Fortissimo motor, not Fortissimo S motor!)
    The motor is a stand-alone, decoupled AC unit. It uses a sophisticated electronic circuit to create 100% clean AC. It is very heavy motor with lot of mass to reduce all the existing vibrations. Motor energy is absorbed by using a sandwich system of metal and MDF. We decided to use a "dual motor design" to eliminate noise in the motor. By using two relatively weak, but silent running motors, we achieve perfect torque.

    The Belt

    Long belts usually have some amount of wobble. To avoid this we use a special silicon string. This movement is also absorbed by the bearing block and by the huge mass of the platter itself.

    The F-Note Tonearm

    (optionally available)
    The F-Note Tonearm is a new E.A.T tonearm design that mixes a high mass tonearm with a low-friction bearing. Due to the high mass these tonearm usually have to use a bearing that is a little bit "slower". The F-Note goes a different way and innovates on a new level. The tonearm is very easy to set up and also a perfect match for the new Jo No. 8 cartridge.

    Massive turntable with Subchassis

    Separate Sub Chassis and a mass loaded turntable

    Platter has 12 brass inserts and one top brass insert under vinyl top plate for increased speed stability and weight of the platter.

    Chrome bearing block

    Bearing spindle with new coating for lowest friction possible

    Optional new F-Note tonearm

    Fortissimo Base optionally available: isolates the turntable perfectly from any resonances from the ground

    Also available as Fortissimo S, in a smaller turntable configuration



    E.A.T. Fortissimo

    Electronic Speed Change

    33.33 / 45.11 RPM

    Speed Variance

    ± 0.09%

    Wow & Flutter

    ± 0.008%

    Signal to Noise Ratio

    -73 dB

    Power Consumption


    Outboard Power Supply

    18 mm

    Power Consumption

    16V/1.000mA AC, suitable for your country's mains supply

    Dimensions  W  × H × D

    700 × 250 × 440 mm


    149 lbs

    Contact us to inquire how you can finance your purchase through our partner, Synchrony.

    Related Products

    Available in store


    Forgot your password?

    • All your orders and returns in one place
    • The ordering process is even faster
    • Your shopping cart stored, always and everywhere